Jump to content


  • Content Count

  • Joined

  • Last visited

About Chasen

  • Rank
  1. for diy user,i recommend Vident iLink400 scanner http://www.obd360.com/wholesale/vident-ilink400full-system-single-make-scan-tool.html
  2. you can search the BMW light control module on this blog,it have many topics on BMW Light control module http://www.car-auto-repair.com
  3. CGDI BMW and BMW AT200 is a perfect match for reading BMW DME ISN code incl. MSV90 MSD85 MSD87 MSD85.2 MSD87.2, B48, N20, N55, N46, MSV80, MSD80 etc. Reading BMW DME ISN code plays an important part in BMW all keys lost key programming. If you want to do all key lost for BMW 3 Series 5 Series 7 Series X5 X6 GT535 Six-cylinder engine, must need ISN code to program the keys. And here are some youtube video guide on how to use CGDI AT200 to read BMW DME ISN code MSD85 ISN Code: MSV90 ISN Code: MSD87 DME ISN Code: Article from:http://blog.uobdii.com/obd-read-bmw-dme-isn-by-cgdi-bmw-or-at200/
  4. Good to know: in BMW which year in Cas 4 or FEM? and which BMW key programmer works? Part 1: Cas 4 or FEM car year Pls look at the chart after 2014 all are fem 1-3 Fxx series FEM , x5-x6 Fxx BDC 5-6-7 series Fxx, x3-x4 Fxx CAS 4 and so on. Part 2: Cas 4 or FEM key programming Here are auto key programmers confirmed to work for Cas 4 and FEM:
  5. The language is stored in the Coding Plug. This is located in chocolate-brown harness connector on the back of the instrument cluster. After 2/89 this is a separate plug on the back of the cluster.When the cluster is first powered up the language is normally German by default. To change the language: 1.Ignition switch in the OFF position. 2.Press and HOLD the right instrument cluster button. 3.Turn the ignition switch to the on position. 4.Wait about 10 seconds. The next language will be displayed. 5.Hold the button until the desired language appears. If the language doesn’t hold one of the following has occurred: a) Code Plug has bad connection. – Check wiring for breaks or shorts. Disconnect and thenreconnect the Coding Plug on the back of instrument cluster. Coding Plug may be defective. Replace Coding Plug. c) Instrument cluster motherboard is dead. When this is the case there are normally otherproblems present, such as : jumpy needles, tripometer resets itself to zero, gong keepssounding even after the brakes are depressed,…etc. E36 OBC V The test function are accessed by pressing the “1000” and “10” buttons simultaneously. Test function(1,10,18,19,& 21) are unlocked and can be called up by inputting the number and pressing ” SET/RES” Number 10 is Language change. BC V TEST FUNCTIONS The BC contains test data values that can be accessed for troubleshooting purposes. The following is a list of the test functions and numbers that are stored in the BC 1.Display test – test all of the LCD segments in the display matrix 2.Momentary consumption (L/100Km) – based on the current “ti”signal and road speed 3.Momentary consumption (L/h) – based on current “ti”signal only 4.Range consumption 5.Momentary range (Km) – range left on fuel in tank when reserve light is on 6.Not used 7.Fuel level from the instrument cluster – average value 8.Momentary speed (Km) – current speed averaged over 2 seconds 9.Operating voltage – available to BC from KL R 10.Language for display – 11.Units readout – for display of mileage/gallons – etc. 12.Average speed for arrival time function 13.Momentary arrival computed 14.ROM – date 15.Readout of fault memory – vendor use only 16.I/O port status – vendor use only 17.Encoding of vehicle specific data – vendor use only 18.Alarm mode – for BC code function – pulse or continuous tone 19.Lock/Unlock function 20.Fuel consumption correction factor 21.Software reset function The test functions are accessed by pressing the “1000” and “10” buttons simultaneously. Test functions #1, #10, #14, #19 and #21 are unlocked and can be called up by entering the number and pressing SET/RES. The other test functions are locked out and test #19 must be used to release the test func-tions for display. The unlock procedure is as follows Call up test #19 – ” LOCK ON” is displayed in the matrix display. Use the number input buttons to enter the sum of the day and month displayed on the clock. Press SET/RES and the computer is now unlocked for display of all test functions To relock the test functions when through with the testing, call up test #19 and press SET/RES twice. E39 OBC http://www.ideaphile.com/bmw/540-obc.html E38 OBC http://home.iae.nl/users/bts/obc.htm E34 OBC http://www.m5springboard.com/Info/E34TestCodes.htm OBC General http://www.eskimo.com/~dalus/bmw/repair_faqs/obc.html E28 OBC http://home.att.net/~ebaines/e28_obc.htm Z3 OBC http://www.z3world.com/z3faq/#Electrical From Auto Repair Technician Home, post How to Change the BMW Instrument Cluster Dashboard Language
  6. hello,how can i tell which type oil is suitable for my car ?
  7. is there any other cable can work with INPA or Expert?
  8. The decoration of your wedding car looks too simple, it is recommended to make it look better.
  9. I found these blog site talk many on BMW Key and remote programming http://www.car-auto-repair.com/tag/bmw-key-program/
  10. Yanhua Mini ACDP Support 93 /24/ 25 / 35/ 95 Series EEPROM in circuit programming (ICP) and on adapter board programming (OBP), and parts of Freescale / NEC MCU in circuit programming (ICP). This module is a necessary basic configuration for other modules. http://www.uobdii.com/wholesale/yanhua-mini-acdp-programming-master.html
  11. you can found OEM part suppliers on internet
  • Create New...